or to view stock quantity and your pricing.
Steiner serves territories in Northern Illinois, Northwest Indiana and Southern Wisconsin. Please for assistance if outside our sales territory.
Banner Engineering Maxi-Beam® RPBA 3/4-Wire Power Block, Photoelectric Sensor, 105 to 130 VAC, SPST Solid State Output
Banner Engineering Maxi-Beam® RPBA 3/4-Wire Power Block, Photoelectric Sensor, 105 to 130 VAC, SPST Solid State Output
SKU13426
MFGR #RPBA
Your Cost: $169.24/ea
List: Power block models RPBA are the most commonly used for ac MAXI-BEAM operation. As the typical hookup shows, they are intended to switch the same ac voltage as is used to power the MAXI-BEAM. However, both can switch any ac voltage that is lower than the supply voltage, as long as both ac circuits share a common neutral. Observe local codes whenever mixing ac voltages in a common wiring chamber. These blocks are designed to handle the inrush current of ac inductive loads like motor starters and solenoids. There is no minimum load requirement, and they will interface directly to inputs of all ac programmable logic controllers (PLCs).
Power block models RPBA are the most commonly used for ac MAXI-BEAM operation. As the typical hookup shows, they are intended to switch the same ac voltage as is used to power the MAXI-BEAM. However, both can switch any ac voltage that is lower than the supply voltage, as long as both ac circuits share a common neutral. Observe local codes whenever mixing ac voltages in a common wiring chamber. These blocks are designed to handle the inrush current of ac inductive loads like motor starters and solenoids. There is no minimum load requirement, and they will interface directly to inputs of all ac programmable logic controllers (PLCs).
Catalog Number RPBA Connection Type Cable Country of Origin US Environmental Conditions -40 to 70 deg C Operating Temperature Gross Weight Per Pack 0.3060 lb Standards CSA, CE Marked, cUL us Listed Suitable For Use With Maxi-Beam® Modularized Photoelectric Sensors Type 3/4-Wire UNSPSC 39121004 UPC 11 66248825545 UPC 12 66248825545 Stock Status NONSTOCK Brand BANNER® Manufacturer Banner Engineering Corp. Output Type SPST Solid State Sensor Type Photoelectric Voltage Rating 105 to 130 VAC Power block is intended to switch the same ac voltage as is used to power the MAXI-BEAM, however both can switch any ac voltage that is lower than the supply voltage, as long as both AC circuits share a common neutral; Range depends on sensor; 4-Wire operation; These blocks are designed to handle the inrush current of AC inductive loads like motor starters and solenoids; There is no minimum load requirement, and they will interface directly to inputs of all AC programmable logic controllers (PLCs) 50/60 Hz, 2 W exclusive of load input 3/4 A maximum (derated to 1/2 A at 70 deg C) output Maximum inrush 10 A for one second or 30 amps for one AC cycle (non-repeating) On-state voltage drop of less than 2.5 VAC at full load Off-state leakage current less than 100 uA Range depends on sensor Wiring chamber 2 m length cable connection
content loaded
content loaded
content loaded
content loaded
- Attributes
- Documents & Resources
- Features
- Substitute Products
| Catalog Number | RPBA |
| Connection Type | Cable |
| Country of Origin | US |
| Environmental Conditions | -40 to 70 deg C Operating Temperature |
| Gross Weight Per Pack | 0.3060 lb |
| Standards | CSA, CE Marked, cUL us Listed |
| Suitable For Use With | Maxi-Beam® Modularized Photoelectric Sensors |
| Type | 3/4-Wire |
| UNSPSC | 39121004 |
| UPC 11 | 66248825545 |
| UPC 12 | 66248825545 |
| Stock Status | NONSTOCK |
| Brand | BANNER® |
| Manufacturer | Banner Engineering Corp. |
| Output Type | SPST Solid State |
| Sensor Type | Photoelectric |
| Voltage Rating | 105 to 130 VAC |
| Power block is intended to switch the same ac voltage as is used to power the MAXI-BEAM, however both can switch any ac voltage that is lower than the supply voltage, as long as both AC circuits share a common neutral; Range depends on sensor; 4-Wire operation; These blocks are designed to handle the inrush current of AC inductive loads like motor starters and solenoids; There is no minimum load requirement, and they will interface directly to inputs of all AC programmable logic controllers (PLCs) |
| 50/60 Hz, 2 W exclusive of load input |
| 3/4 A maximum (derated to 1/2 A at 70 deg C) output |
| Maximum inrush 10 A for one second or 30 amps for one AC cycle (non-repeating) |
| On-state voltage drop of less than 2.5 VAC at full load |
| Off-state leakage current less than 100 uA |
| Range depends on sensor |
| Wiring chamber |
| 2 m length cable connection |